Prepare the HP-UX machine

 

+
Search Tips   |   Advanced Search

 

Configure HP-UX kernel settings before installing

To set kernel parameters, perform the following steps:

  1. Log into the host machine with superuser (root) privileges.

  2. Determine the physical memory, which know to avoid setting certain kernel parameters above the physical capacity:

    1. Start the HP-UX System Administration Manager (SAM) utility.

    2. Select Performance Monitors > System Properties > Memory.

    3. Note the value for Physical Memory and click OK.

    4. Exit from the SAM utility.

  3. Set the maxfiles and maxfiles_lim parameters to at least 4096. (The table below recommends 8000 and 8196, respectively. You must first edit the /usr/conf/master.d/core-hpux file, to allow the SAM utility to set values greater than 2048:

    1. Open the file /usr/conf/master.d/core-hpux in a text editor.

    2. Change the line," *range maxfiles<=2048" to "*range maxfiles<=60000"

    3. Change the line, "*range maxfiles_lim<=2048" to "*range maxfiles_lim<=60000"

    4. Save and close the file. Old values might be stored in the /var/sam/boot.config file. Force the SAM utility to create a new boot.config file:

      1. Move the existing version of the /var/sam/boot.config file to another location, such as the /tmp directory.

      2. Start the SAM utility.

      3. Select Kernel Configuration > Configurable Parameters. When the Kernel Configuration window opens, a new boot.config file exists.

        Alternatively, rebuild the boot.config file with this command:

        # /usr/sam/lbin/getkinfo -b 

  4. Set new kernel parameter values:

    1. Start the SAM utility.

    2. Select Kernel Configuration > Configurable Parameters.

    3. For each of the parameters in the following table, perform this procedure:

      1. Highlight the parameter to change.

      2. Select Actions > Modify Configurable Parameter.

      3. Type the new value in the Formula/Value field.

      4. Click OK.

    When WebSphere Portal and DB2 are installed on the same machine, some kernel values are higher than those shown in the table below. If you are using this configuration, refer to the following topics for more information:

    Typical kernel settings for running WebSphere Portal appear in the following table:

    Parameter Value
    dbc_max_pct 25
    maxdsiz 805306358
    maxdsiz 2048000000 (when WebSphere Application Server Base and Network Deployment products are on the same machine)
    maxfiles_lim 8196 (Change this one before maxfiles.)
    maxfiles 8000
    maxssiz 8388608
    maxswapchunks 8192
    max_thread_proc 3000
    maxuprc 512
    maxusers 512
    msgmap 2048
    msgmax 65535
    msgmax 131070 (when WebSphere Application Server Base and Network Deployment products are on the same machine)
    msgmnb 65535
    msgmnb 131070 (when WebSphere Application Server Base and Network Deployment products are on the same machine)
    msgmni 50
    msgseg 32767
    msgssz 32
    msgtql 2046
    nfile 58145
    nflocks 3000
    ninode 60000
    nkthread 7219
    nproc 4116
    npty 2024
    nstrpty 1024
    nstrtel 60
    sema 1 (with Embedded Messaging)
    semaem 16384 (with Embedded Messaging)
    semmap 514
    semmni 2048
    semmns 16384 (with Embedded Messaging)
    semmnu 1024
    semume 200
    semvmx 32767 (with Embedded Messaging)
    shmmax 2147483647
    shmem 1 (with Embedded Messaging)
    shmmni 1024
    shmseg 1024
    STRMSGSZ 65535

  5. Select Actions > Process New Kernel.

  6. Click Yes on the information window to confirm the decision to restart the machine.

    Follow on-screen instructions to restart your machine and to enable the new settings.

 

Related information