sttydefs

 

---

 
 
 
 Maintenance Commands                                 sttydefs(1M)
 
 
 


NAME
      sttydefs - maintain line settings and hunt sequences for TTY
      ports
 


SYNOPSIS
      /usr/sbin/sttydefs -a ttylabel  [ -b ]  [  -f final-flags  ]
      [ -i initial-flags ]  [ -n nextlabel ]
 
      /usr/sbin/sttydefs -l  [ ttylabel ]
 
      /usr/sbin/sttydefs -r ttylabel
 


DESCRIPTION
      sttydefs is an administrative  command  that  maintains  the
      line  settings and hunt sequences for the system's TTY ports
      by  making  entries  in,  and  deleting  entries  from   the
      /etc/ttydefs file.
 
      sttydefs with a -a or -r option may be invoked only  by  the
      super-user.  sttydefs  with -l may be invoked by any user on
      the  system.
 


OPTIONS
      The following options are supported:
 
      -a ttylabel
            Add a record to the ttydefs file,  using  ttylabel  as
            its  label.  The following describes the effect of the
            -b, -n, -i, or -f options  when  used  in  conjunction
            with the -a option:
 
      -b    Enable autobaud. Autobaud allows the system to set the
            line  speed  of  a given TTY port to the line speed of
            the device connected to the port without
             the user's intervention.
 
      -f final-flags
            Specify the value to be used in the final-flags  field
            in   /etc/ttydefs.  final-flags  must  be  in a format
            recognized by the stty command.  final-flags  are  the
            termio(7I)  settings  used by ttymon after receiving a
            successful connection request and  immediately  before
            invoking  the  service  on the port. If this option is
            not specified, sttydefs will set final-flags equal  to
            the termio(7I) flags 9600 and sane.
 
      -i initial-flags
            Specify the value to  be  used  in  the  initial-flags
            field  in   /etc/ttydefs.  initial-flags  must be in a
            format recognized by the stty command. These flags are
            used  by  ttymon  when searching for the  correct baud
            rate. They are set prior to  writing  the  prompt.  If
 
 
 
 SunOS 5.8           Last change: 14 Sep 1992                    1
 
 
 
 
 
 
 Maintenance Commands                                 sttydefs(1M)
 
 
 
            this  option  is  not  specified,  sttydefs  will  set
            initial-flags equal to the termio(7I) flag 9600.
 
      -n nextlabel
            Specify the value to be used in the nextlabel field in
            /etc/ttydefs.   If   this  option  is  not  specified,
            sttydefs will set nextlabel equal to ttylabel.
 
      -l[ttylabel]
            If a ttylabel  is  specified,  sttydefs  displays  the
            record  from  /etc/ttydefs whose TTY label matches the
            specified  ttylabel.  If  no  ttylabel  is  specified,
            sttydefs displays the entire contents of /etc/ttydefs.
            sttydefs verifies  that  each  entry  it  displays  is
            correct  and  that  the entry's nextlabel field refer-
            ences an existing
 
      -r ttylabel
            Remove any record in the ttydefs file  that has ttyla-
            bel as its label.
 
 OUTPUT
      If successful, sttydefs  will  exit  with  a  status  of  0.
      sttydefs -l will generate the requested information and send
      it to standard output.
 
 EXAMPLES
      Example 1: A sample of sttydefs command.
 
      The following command lists all the entries in  the  ttydefs
      file and prints an error message for each invalid entry that
      is detected.
 
      example# sttydefs -l
 
      The following shows a command that requests information  for
      a single label and its output:
 
      example# sttydefs -l 9600
      ------------------------------------------------------------------
      9600:9600 hupcl erase ^h:9600 sane ixany tab3 hupcl erase ^h::4800
      ------------------------------------------------------------------
      ttylabel: 9600
      initial flags: 9600 hupcl erase ^h
      final flags:   9600 sane ixany tab3 hupcl erase ^h
      autobaud: no
      nextlabel:      4800
      The following sequence of commands will add the labels 1200,
      2400, 4800, and 9600 and put them in a circular list:
 
      sttydefs -a 1200 -n 2400 -i 1200 -f "1200 sane"
      sttydefs -a 2400 -n 4800 -i 2400 -f "2400 sane"
 
 
 
 SunOS 5.8           Last change: 14 Sep 1992                    2
 
 
 
 
 
 
 Maintenance Commands                                 sttydefs(1M)
 
 
 
      sttydefs -a 4800 -n 9600 -i 4800 -f "4800 sane"
      sttydefs -a 9600 -n 1200 -i 9600 -f "9600 sane"
 


FILES
      /etc/ttydefs"
 


ATTRIBUTES
      See attributes(5) for descriptions of the  following  attri-
      butes:
 
      ____________________________________________________________
     |       ATTRIBUTE TYPE        |       ATTRIBUTE VALUE       |
     |_____________________________|_____________________________|
     | Availability                | SUNWcsu                     |
     |_____________________________|_____________________________|
 
 


SEE ALSO
      attributes(5), termio(7I)
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 SunOS 5.8           Last change: 14 Sep 1992                    3
 
 
 

---